Sold out
1 1
Limited Time Offer Ends in
Emart Express

GLUEDEVIL SENSOR GREY GASKET MAKER 70ML

GLUEDEVIL SENSOR GREY GASKET MAKER 70ML

50-GM2250

R 89.99 ZAR
R 89.99 ZAR
  • Shipping is free for orders over R 499
  • Delivery within 2-5 working days
  • 14-Days returns with the option of a refund, or replacement, available on all online orders. Learn more
Visa Card Accepted MasterCard Accepted PayFast Accepted
View full details
PRODUCT NAME:

GLUEDEVIL SENSOR GREY GASKET MAKER

ITEM PART NO: 50-GM2250

PRODUCT: GD 70ML GREY SENSOR SILICONE

GLUEDEVIL Sensor Grey is a one-component, oxime cure, silicone adhesive sealant which cures at room temperature with moisture in the air. This product bonds to most materials, such as metals, plastics, ceramics and glass without the use of primers.

KEY FEATURES:
  • Primer less adhesion to many substrates
  • Neutral cure; Little risk of corrosion (corrosion to copper and copper alloys)
  • Excellent high and low temperature resistance; from -60°C to +330°C
  • Excellent weather ability, ozone, and chemical resistance
  • Excellent electrical insulation properties
  • Simple and easy-to-use one-component system
APPLICATIONS:
  • A waterproof sealant for electrical and communication equipments
  • Air-tight sealants for meters to keep out water and dust
  • Wind shield sealants for automobiles and ships
  • Oil leakage preventive sealants for automobile engine parts
  • Sealing and potting to equipments which require cold and heat resistance and flame retardant
  • General adhesion for metals, glass, plastic, wooden, etc
TYPICAL PROPERTY DATA:
TYPICAL UNCURED PROPERTIES:
Appearance Non-flow able paste
Tack-free time(23°C)                                     min 10
TYPICAL CURED PROPERTIES:   (7days@23°C/50%RH)
Appearance Elastic rubber
Specific gravity 1.04
Hardness(Type A) 28
Tensile strength                                               MPa{kgf/cm2} 1.9 {19}
Elongation                                                         % 380
Adhesive strength*                                        MPa{kgf/cm2} 1.7 {17}
Thermal conductivity                                     W/(m·K){cal/(cm·s·°C)} 0.18{4.4✕10-4}
Volume resistivity 1✕107{1✕1015}
Dielectric strength                                         kV/mm 23
Dielectric constant(60Hz) 2.9
Dissipation factor(60Hz) 0.004

* Aluminum Lap shear

ADHESION PERFORMANCE:

GLUEDEVIL Sensor Grey has excellent bonding properties and adheres to many materials without primers. However, for significantly better adhesion on difficult-to-bond substrates, use of a primer is suggested. The following list of materials shows the quality of adherence of GD Sensor Grey used both with ME121,ME123, XP80-A5363 or without a primer.

SUBSTRATE
NO PRIMER
ME121
ME123
XP80-A5363
Metals
Copper Ì✶ {✶
Steel { {
Mild steel { {
Brass Ì✶ {✶
Stainless steel Ì {
Aluminum { {
Corrosion-resistant aluminum { {
Galvanized sheet iron { {
Tin plate { {
Plastics
Acrylic resin {
Phenolic resin {
Epoxy resin {
Soft poly vinyl chloride {
Rigid poly vinyl chloride { { {
Polyester film { { {
Unsaturated polyester resin { { {
Polyimide { { {
ABS resin { { {
Polypropylene(PP) {
Polyethylene(PE)
Fluoride resin
Silicone varnish laminate { {
Silicone varnish coated glass cloth { {
Rubbers
Chloroprene (CR) Ì {
Nitryl (NBR) Ì {
Styrene butadiene(SBR) Ì {
Ethylene propylene(EP) Ì {
Silicone-HCR { {
Inorganic materials
Glass { {
Mortar Ì {
ALC Ì {
Ceramic { {
Wood
Cedar { {
Cypress { {
Lauan Ì Ì

Note:

{: Excellent(Cohesive failure)

Ì: Not sufficient

: Poor (Adhesive failure)

✶: Corrosion may occur depending on the application

Do not apply to Polycarbonate due to solvent crack

HANDLING AND SAFETY:
  • Wear eye protection and protective gloves when handling uncured sealant as it can irritate ey In case of eye contact, immediately flush eyes well with water and contact a physician.
  • Substrate surface should be thoroughly cleaned with a suitable solvent such as alcohol, xylene, methyl ethyl ketone (MEK)et
  • This product releases methyl ethyl ketoxime vapors as a by-product of c
  • Adequate ventilation must be maintained in the workplace at all times.
  • Extended contact with the skin may cause irritation and should be avoi
STORAGE:
  • Store in a cool, dry place out of direct sunlight.
  • Keep out of the reach of the children
PACKAGING:
  • 70ml tube available in case of 12

All the information of Material Safety Data Sheet is provided on the basis in good faith, and is believed to be trustworthy but is for reference only.  National Adhesive Distributors cc cannot accept any liability for the results whatsoever arising from the use of National Adhesive Distributors products due that the utilization of these products is simply out of our control. The users are responsible for selecting the suitability of the products and methods of use.    

Recent viewed